Volvo 9700 ELD Interface Kit for OBD Vehicles

SEOCONTENT-START

Writer: <QF7720959 rev 5>
Instruction Sheet IS-19914
Volvo 9700 ELD Interface Kit for OBD Vehicles
First Release
06-27-2019
APPLICATION
Model
VIN
Volvo 9700
Model Year : 2014 and up
From 3CET2S222E5162000 up to 3CET2V923J5191913
MATERIAL
Order Kit # 7775126 which includes the following parts:
Part No.
Description
Qty
23446648
ELD Harness OBD
1
20890176
Control Unit FMS Gateway
1
390038
ELD Decal
1
23338070
OBD Decal (Volvo)
1
952641
Adel Clamp Rub #35
1
952634
Adel Clamp Rub #24
1
500124
Screw SS #8X1/2
4
504637
Cable tie Nylon STD Black
15
FI-19914
Instruction Sheet (FR)
1
IS-19914
Instruction Sheet (EN)
1
Equipment required:
Description
Qty
Laptop with PTT (Premium TechTool, latest version installed) & related cables.
1
NOTE
Material can be obtained through regular channels.
IS-19914
Page 2 / 11
Writer: mg <QF7720959 rev 5>
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition switch to the OFF position. Wait 20 seconds and set the main switch and the battery switch to the OFF position. Disconnect negative terminals from the batteries.
Lock out & Tag out (LOTO) must be performed during set-up, maintenance or repair activities. Refer to your local procedure for detailed information regarding the control of hazardous energy.
PART 1: FMS GATEWAY MODULE INSTALLATION
1. Open the electrical compartment located behind the driver’s seat.
2. Remove both drivers’ lateral utility compartment doors.
IS-19914
Page 3 / 11
Writer: mg <QF7720959 rev 5>
3. Remove the vehicle OBD connector from the underside of the dashboard (drivers’ side).
– Unclip the black plastic cap securing the connector to the bracket (do not discard the plastic cap).
– Remove the connector from the bracket.
4. Route the ELD interface harness 23446648 from the electrical compartment up to the driver’s area (OBD connector area).
IS-19914
Page 4 / 11
Writer: mg <QF7720959 rev 5>
– From the electrical compartment, route the OBD side of the harness (with red connector) inside the lateral utility compartment.
– Pass the harness from the lateral compartment to the driver’s foot area (OBD connector area).
5. Connect the vehicle OBD connector (previously removed from the bracket) to the ELD harness red connector.
IS-19914
Page 5 / 11
Writer: mg <QF7720959 rev 5>
6. Secure the ELD harness OBD connector (black) to the bracket.
– Insert the connector in the bracket opening and secure (clip in place) using the black plastic cap.
7. Inside the electrical compartment, secure the ELD FMS gateway module 20890176 to the compartment wall inside the dotted area shown.
– Make a support bracket for the module using the supplied #35 Adel clamp 952641 as shown.
IS-19914
Page 6 / 11
Writer: mg <QF7720959 rev 5>
– Secure the module to the compartment wall using the supplied 500124 screws (module connector facing down). Connect the ELD harness green connector to the gateway module.
8. (Optional step) If using a Volvo branded ELD device (part # 7770385 or 7770388). Secure the ELD device next to the gateway module using the supplied #24 Adel clamp 952634 (connector facing down).
– Make a support bracket for the module using the Adel clamp and secure to the electrical compartment wall next to the FMS Gateway module.
– Connect the module to the ELD harness round 9 PIN connector (remove gray protective cap) using the adaptor cable supplied with the ELD module.
IS-19914
Page 7 / 11
Writer: mg <QF7720959 rev 5>
NOTE
Do not discard the gray protective cap.
Secure the cap to the cable using a small cable tie.
9. Secure the ELD harness inside the electrical compartment, at the bottom of the lateral utility compartment and under the dash using cable ties.
CAUTION
Make sure the harness is not interfering with the controls or the driver’s movements under the dash area.
10. Install ELD and OBD warning decals.
– Install the OBD decal 23338070 on the lower part of the dashboard (above the OBD connector). When using a Volvo ELD device, also install the ELD decal 390038 over the ELD device in the electrical compartment.
11. Reinstall the electrical compartment cover and lateral compartment doors.
IS-19914
Page 8 / 11
Writer: mg <QF7720959 rev 5>
PART 2: FMS GATEWAY MODULE PROGRAMMING
1. Connect to PTT (Premium Tech Tool) and confirm in the product tab that the FMS gateway (MID 179) is present in the Product Data but not in the Central Data.
2. In Premium TechTool, select PROGRAM tab. In PROGRAM tab, select operation 1700-22-03-06 Accessory Kit then clicks START.
IS-19914
Page 9 / 11
Writer: mg <QF7720959 rev 5>
3. Enter Accessory kit number 85153392 Click on PROGRAM button below and then follow the instructions. The programming process will start.
4. If the following message pops-up click YES.
IS-19914
Page 10 / 11
Writer: mg <QF7720959 rev 5>
5. When prompted, proceed with the following actions:
– Turn the ignition key to the OFF position.
– Wait 10 seconds.
– Turn the ignition key to the ON position.
NOTE
Second programming step “Reading out transferable parameters from affected Electronic Control Units” will show as incomplete with this symbol ; This is normal with a new module installation.
6. Wait for the program to upload; this can take a few minutes.
IMPORTANT – If an error message regarding code 118 “Failed to read fault codes” shows up, click NO. This will not affect the programming although programming will mark as failed.
IS-19914
Page 11 / 11
Writer: mg <QF7720959 rev 5>
7. Once completed, make sure the FMS gateway is now visible in the Central Data and all other related sections as shown below.
8. Refresh and delete codes.
PARTS / WASTE DISPOSAL
Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)

SEOCONTENT-END